Beauteous Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)




Sterling Silver Crescent and Bead Earrings

MATERIALS Wanted
three" 4 x 1 mm sterling silver rectangle wire
Twenty-one particular 'Λ* head pins
Two turquoise disc beads
Just one Vi* one.seven mm black hollow rubber tube
Two sterling silver ear wires
What guidance would you give you a commencing artist?
“Do what you adore. Investigate diverse media. Offer with a selective, limited, basis initially to find out what will work or what won't be just right for you before you jump into a major outlay of money and effort.*
-Sally J. Phillips Jewelry Designer
Equipment Essential
Ruler
Marker
Jeweler's observed or tin snips Protection Eyeglasses Tricky, flat surface Awl
Hammer /is" drill bit
Hand held rotary Instrument, flex shaft, or drill press File
Fantastic grit sanding pad
Ring mandrel
Rawhide mallet
Two pairs of chain nose pliers
Scissors
Wire cutters or tin snips Round nose pliers


1.Make use of the ruler to evaluate and mark two one Vi’ items of four x one mm rectangle sterling silver wire.
2Using a jeweler's noticed or tin snips, Slice the four x one mm rectangle sterling silver wire into two one Vi’ lengths.
three.File Just about every close of your 1Vi" rectangle wire pieces to remove any burs or rough edges.
If desired, You should use the file to round the ends from the rectangle wire pieces. Use a good grit sanding pad to go more than the realm where you have filed to easy the edges and remove any file marks.
4.Use the ruler to measure and mark /*." from one end of the 1 Vi’ pieces of rectangle wire and place a mark in the middle of your wire. This is when you can drill the holes to slip The pinnacle pins by.
five.Place on your own basic safety Eyeglasses!!! Spot the 1 Vi" rectangle wire pieces onto a hard, flat surface. Place The purpose of your awl over the mark that you choose to built Vm,' from a person close with the rectangle wire parts, and firmly strike after on the highest on the awl using a hammer. This can make a pilot hole for drilling holes into the rectangle wire.

Sterling Silver Crescent and Bead Earrings
Chapter 5

six.Employing a /is" drill little bit. drill holes into one Mens Ring particular stop in the rectangle wire pieces with a handheld rotary tool, flex shaft, or drill push (when however donning your security glasses!).
7.Utilize the file or high-quality grit sanding pad to do away with any burs or tough edges still left from drilling holes in to the rectangle wire pieces.
eight.Curve both equally 1W items of rectangle wire into a mens ring “C" shape employing a ring mandrel and rawhide mallet. If you don't have a hoop Men's Rings mandrel and rawhide mallet, use two pair of chain nose pliers. Holding a person set Mens RingMen's Rings of pliers in Every single hand, grasp Every single finish from the one Vi* rectangle wire piece Along with the pliers and Carefully bend the rectangle wire into a “C* shape. Look at both equally on the C-shaped rectangle wire pieces and regulate the curves so that they're equivalent in si2e. Set these apart.
nine.Make use of the ruler to measure and mark the rubber tube into 4 equivalent items measuring Vm’ each. Use scissors to chop the rubber tube.
ten.Spot the turquoise disc bead onto The pinnacle pin and insert a single V·' piece of the rubber tube, put The top pin with the hole during the C-formed rectangle wire, after which add one other V«" bit of rubber tube.

13. Keep The top pin With all the bead, rubber tube, and also the rectangle wire on it in a single hand Together with the wire which you bent pointing toward you. Utilizing the round nose pliers, grip the end of The pinnacle pin wire which is pointing toward you and roll it clear of you (think about turning the ignition important to get started on your vehicle). Release the pliers from The pinnacle pin wire.
At this time, the opening within the loop at the best of The top pin wire ought to still be substantial ample to slip the ear wire on. When you insert the ear wire, make use of the round nose pliers to grasp the loop of The pinnacle pin wire and roll it closed. You can use the spherical nose or chain nose pliers to adjust The form of your loop at the highest of The top pin if you have to.
eleven. Make use of the ruler to measure and mark /(.’ higher than the very best piece of the hollow rubber tube. Along with the wire cutters or tin snips, Lower the head pin wire Yu.’ earlier mentioned the highest from the hollow rubber tube.
twelve. Make use of the chain nose pliers to bend the head pin wire beside the very best of the rubber tube in a 90-diploma angle.
fourteen. Repeat these actions for the 2nd earring.







 

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Beauteous Sterling Silver Rectangle Wire,Hollow Rubber Tube, and Turquoise Earrings(jewelry tutorial)”

Leave a Reply

Gravatar